I'll have to check that, but I swear I have already several times. Just been about a month now since I've looked at it. I hope it's that simple, but unfortunately for me... I believe it's something else. I'll let you know though and thanks for the idea.
1
HELP... post CC plate install... THUNK
Started by
07SGT5687
, Sep 15 2012 07:42 PM
21 replies to this topic
#21 OFFLINE
07SGT5687
-
- Members
-
- 1,237 posts
- Joined 06-July 10
el gato diablo
- Gender:Male
- Region:Mountain
- Vehicle:Shelby GT
Posted 17 December 2012 - 12:41 PM
CSM 07SGT5687 - "Stella" - Ford Build Date - 05/17/07 ----> Shelby Build Start Date - 09/12/07 ----> Shelby Build Completion Date - 09/13/07 ----> In-Service Date - 10/15/07
Factory Options: 5spd, Heated Seats, Shaker 500, IUP, Alarm Aftermarket Adds: FRPP Whipple 550HO, "SHELBY GT" valve covers, JLT Carbon Fiber CAI, Jon Lund tune, Shelby/C&R High Capacity Radiator and Dual Fan Intercooler, Moroso Intercooler tank and coolant tank, Dynotech Aluminum One-piece Drive shaft, Shelby/MM Caster/Camber Plates, Thump Racing HD Belt Tensioner, JLT oil separator, Serpentine Belt Shredder, Autometer Nexus gauges in SOS triple A-pillar pod, "SHELBY GT" engine cap set, "SHELBY" anodized fuel door, "SHELBY" Hood Pins, 20" Gun Metal Shelby Razors (24mm) with Nitto 555s, Baer 6S - 6 piston Front Brake kit, Baer Eradispeed +2 Rear Brake kit, Hawk HPS (street) pads, Bob's Autosport Axle Reservoir, Fender Stripe, Sequential Turn Signals/Brake Lights, CG Locks, 10% Tint, Pioneer AVIC-Z120BT, Beltronics Pro RX65 Blue hardwired...
Track Setup: 18" x 8.5" TSW Nurburgring (45mm) - TOO NARROW, Nitto NT-01 275/40/18 - TOO FAT/TALL, and Carbotech XP10/20 track pads - jury is still out, Corbeau harness bar, Corbeau 5 point harnesses.
496rwhp/473rwtq on a fully-loaded Dynojet... that'll work for now...
Factory Options: 5spd, Heated Seats, Shaker 500, IUP, Alarm Aftermarket Adds: FRPP Whipple 550HO, "SHELBY GT" valve covers, JLT Carbon Fiber CAI, Jon Lund tune, Shelby/C&R High Capacity Radiator and Dual Fan Intercooler, Moroso Intercooler tank and coolant tank, Dynotech Aluminum One-piece Drive shaft, Shelby/MM Caster/Camber Plates, Thump Racing HD Belt Tensioner, JLT oil separator, Serpentine Belt Shredder, Autometer Nexus gauges in SOS triple A-pillar pod, "SHELBY GT" engine cap set, "SHELBY" anodized fuel door, "SHELBY" Hood Pins, 20" Gun Metal Shelby Razors (24mm) with Nitto 555s, Baer 6S - 6 piston Front Brake kit, Baer Eradispeed +2 Rear Brake kit, Hawk HPS (street) pads, Bob's Autosport Axle Reservoir, Fender Stripe, Sequential Turn Signals/Brake Lights, CG Locks, 10% Tint, Pioneer AVIC-Z120BT, Beltronics Pro RX65 Blue hardwired...
Track Setup: 18" x 8.5" TSW Nurburgring (45mm) - TOO NARROW, Nitto NT-01 275/40/18 - TOO FAT/TALL, and Carbotech XP10/20 track pads - jury is still out, Corbeau harness bar, Corbeau 5 point harnesses.
496rwhp/473rwtq on a fully-loaded Dynojet... that'll work for now...
Team Shelby Members: Stop by and pin up your location on the TeamShelby.com member map at ZeeMaps.com
#22 OFFLINE
Albino500
-
- Team Shelby Club Member
-
- 905 posts
- Joined 19-March 12
Team Shelby Member
- Gender:Male
- Region:Pacific Coast
- Interests:Open track and WOT
- Vehicle:GT500
Posted 17 December 2012 - 01:25 PM
You can always jack the front end up so that the tires are just a couple of inches off the ground and place jack stands under the frame then take a long bar and place it under the tire and lift upwards then release to see if you can get the noise to happen . Get a second person to help - if they lift up/down then you can put your hand on different components to feel for the play/noise source . Kudos to fatboy for finding his problem and good luck to 07SGT5687.
2007 GT500 Built on 7/27/2006
#918 of a build of 8152 coupes
#212 of 2252 in Performance White
Member of Terlingua Racing Team
Member of the "Clean Butt Club" - Class of 2010
2012 Shelby American 50th Anniversary Vegas Bash Car Show "Class" Award Winner
2007 SGT-California Edition Built on 5/15/2007
CSM#07SGT4755
1 of 89 Shelby GT-California Editions done in Performance White/Silver Stripes
Converted to " SCCA SMG Class " race car - 2/04/2013
#918 of a build of 8152 coupes
#212 of 2252 in Performance White
Member of Terlingua Racing Team
Member of the "Clean Butt Club" - Class of 2010
2012 Shelby American 50th Anniversary Vegas Bash Car Show "Class" Award Winner
2007 SGT-California Edition Built on 5/15/2007
CSM#07SGT4755
1 of 89 Shelby GT-California Editions done in Performance White/Silver Stripes
Converted to " SCCA SMG Class " race car - 2/04/2013
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
