Jump to content





Photo

Hood pin lanyards


  • Please log in to reply
3 replies to this topic

#1 OFFLINE   H0050

H0050

    H0050

  • Pacific Coast Region
  • 5,832 posts
  • Joined 28-September 07
  • Region:Pacific Coast
  • Interests:Cars, wakeboarding, fishing & family
Garage View Garage

Posted 21 October 2012 - 09:03 PM

Anyone change their hood pin lanyard? What size drill bit did you use to drill out & what size rivet did you use for the new lanyard?

Thanks.
Harald #50

CSM 06H0050: Registered as a Shelby GT-H/SC
Black CS 69 w/ 255/45/18 & 285/40/18 BFG G-Force KDW
Lower Billet Grill
Air Bag Signed by Carroll Shelby, Amy Boylan, Gary Davis, Gary Patterson, Cleo Shelby & Akos Feher
40th Anniversary Signature Floor Mats w/ Gold Stripes
Shelby GT Plus & Eradispeed 14" brakes & S/S brake lines
Sequential Tail lights
GTH Billet Fluid Caps
SAI installed polished Paxton SC # 0066 w/ GT 500 fuel pump
GT-H/SC side stripes
Shelby gauges & gauge pod
424RWHP 367 Torque
KR rear end expansion tank
2009 Shelby Bash top 20 winner
2011 Bash In & Out cruise recognition plaque
Painted over the top stripes
Terlingua Deep Draw Hood
2014 Vegas Bash Show & Shine Class Winner 2015 Shelby American Las Vegas Bash Top 25 car show Award

The race is run, the flag unfurled, the champion now will rest.
God speed, Carroll Shelby, we will never forget you.
CARROLL H SHELBY

Jan. 11, 1923 May 10, 2012


http://i414.photobuc...8/06h50/030.jpg
http://i414.photobuc...8/06h50/035.jpg
http://i414.photobuc...8/06h50/037.jpg

#2 OFFLINE   19again

19again

    Team Shelby Illinois Director

  • Team Shelby State Director
  • 607 posts
  • Joined 14-June 09
  • Region:Great Lakes
  • Interests:Of course Mustangs,a 65 and 06 in two different garages! F1 and the Autobahn in the Chicago area.
    MCA 20457
Garage View Garage

Posted 22 October 2012 - 03:39 PM

Harald I used a 1/8 drill I think with a 1/8 stainless rivet. Did you purchase the kit from SPP? What I found is the lanyard seems to be a bit to long. When I am flying down the highway they flop around. Others that I have seen, maybe originals aren't as long and seemed to be dressed better over the hood.
06H352 {Tampa Hertz}


Team Shelby Illinois Director


Hertz put me in the drivers seat

#3 OFFLINE   H0050

H0050

    H0050

  • Pacific Coast Region
  • 5,832 posts
  • Joined 28-September 07
  • Region:Pacific Coast
  • Interests:Cars, wakeboarding, fishing & family
Garage View Garage

Posted 22 October 2012 - 04:56 PM

Harald I used a 1/8 drill I think with a 1/8 stainless rivet. Did you purchase the kit from SPP? What I found is the lanyard seems to be a bit to long. When I am flying down the highway they flop around. Others that I have seen, maybe originals aren't as long and seemed to be dressed better over the hood.


Thanks Did you snake them through/around hood post. Thats how I noticed most were done and that eliminates the large loop flopping. .
Harald #50

CSM 06H0050: Registered as a Shelby GT-H/SC
Black CS 69 w/ 255/45/18 & 285/40/18 BFG G-Force KDW
Lower Billet Grill
Air Bag Signed by Carroll Shelby, Amy Boylan, Gary Davis, Gary Patterson, Cleo Shelby & Akos Feher
40th Anniversary Signature Floor Mats w/ Gold Stripes
Shelby GT Plus & Eradispeed 14" brakes & S/S brake lines
Sequential Tail lights
GTH Billet Fluid Caps
SAI installed polished Paxton SC # 0066 w/ GT 500 fuel pump
GT-H/SC side stripes
Shelby gauges & gauge pod
424RWHP 367 Torque
KR rear end expansion tank
2009 Shelby Bash top 20 winner
2011 Bash In & Out cruise recognition plaque
Painted over the top stripes
Terlingua Deep Draw Hood
2014 Vegas Bash Show & Shine Class Winner 2015 Shelby American Las Vegas Bash Top 25 car show Award

The race is run, the flag unfurled, the champion now will rest.
God speed, Carroll Shelby, we will never forget you.
CARROLL H SHELBY

Jan. 11, 1923 May 10, 2012


http://i414.photobuc...8/06h50/030.jpg
http://i414.photobuc...8/06h50/035.jpg
http://i414.photobuc...8/06h50/037.jpg

#4 OFFLINE   07ShelbyGT2908

07ShelbyGT2908

    Team Shelby New Member

  • Members
  • Pip
  • 115 posts
  • Joined 28-April 14
  • Region:Decline
  • Interests:Shelby GT #2908
    Mustangs Of All Sorts

Posted 11 January 2015 - 03:20 PM

Hey Guys,

 

Old thread but changing out my lanyards as well. The size 1/8 rivet? I mean are they 1/8 grip 1/8 diameter or are they 1/8 grip and 3/16 diameter?

 

Thanks,

 

Francis






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users